The Phonitor x is the ultimate headphone amplifier. Thanks to VOLTAiR technology it powers headphones operated both balanced and unbalanced playfully with up to 3.7 W.
XLR InputNeutrik XLR, balanced, Pin 2 = (+) | |
---|---|
Impedance | ca. 20 kohms |
CMR | -82 dBu (at 1 kHz) |
Max. Input Level | +32.5 dBu |
RCA Input | |
RCA, unbalanced (single-ended) | |
Impedance | ca. 10 kohms |
Max. Input Level | +32.5 dBu |
Digital Inputs (optional) | |
Coaxial SPDIF (RCA) | |
Optisch TOSLINK (F06) | |
USB (B) | |
Sample Rates (kHz) | 44.1, 48 , 88.2, 96, 176.4, 192 |
Balanced Headphone Output | |
Neutrik 4-pin XLR connector | |
Pin wiring | 1= L (+), 2= L (-), 3= R (+), 4= R (-) |
Impedance | 0.36 ohms |
Damping Factor | 180 @ 40 ohms |
Frequency Range | 10 Hz to 300 kHz ( -3 dB) |
Crosstalk at 1kHz | -90 dB |
THD & N | 0.00091 % (at 0 dBu, 1kHz, 100 kohms load) |
Noise (A-weighted) | -98 dBu |
Dynamic Range | 130.5 dB |
Unbalanced Headphone Output | |
6.35 mm TRS connector | |
Pin wiring | Tip = Left, Ring = Right, Sleeve = GND |
Impedance | 0.18 ohm |
Attenuation Factor | 180 @ 40 ohms |
Frequency Range | 10 Hz to 300 kHz ( -3 dB) |
Crosstalk at 1kHz | -90 dB |
THD & N | 0.00091% (at 0 dBu, 1 kHz, 100 kohms load) |
Noise (A-weighted) | -103 dB |
Dynamic Range | 135.5 dB |
Max. Output Power (at +30 dBu @ 1 kHz) | |
2 x 1 W at 600 Ohm impedance | |
2 x 2 W at 300 Ohm impedance | |
2x 3.7 W at 120 Ohm impedance | |
2x 2.9 W at 47 Ohm impedance | |
2x 2.7 W at 32 Ohm impedance | |
Speaker/Line Outputs | |
Neutrik XLR, balanced, Pin 2 = (+) | |
RCA, unbalanced (single-ended) | |
Frequency Range | 4 Hz to 300 kHz (-3 dB) |
Crosstalk at 1 kHz | -106 dB |
THD & N | 0.00085 % (at 0 dBu, 1 kHz, 100 kohms load) |
Noise (A-weighted) | -103.8 dB |
Dynamic Range | 136.3 dB |
Internal Operating Voltages | |
Analog | +/- 60 V |
Digital | + 5 V and + 3,3 V (optional) |
Power Supply | |
Mains voltage (switchable) | 230 V AC / 50 Hz or 115 V AC / 60 Hz |
Fuses | 230 V|| T 500 mA; 115 V|| T 1 A |
Power consumption | max 40 VA |
Stand-by power consumption | 0.7 W |
Dimensions (incl. feet) | |
278 mm W x 100 mm H x 335mm D | |
10.95 in W x 3.94 in H x 11.19 in D | |
Weight | |
4.3 kg; 9.5 lbs (unit only) | |
5.4 kg; 11.9 lbs (shipping) |
The headphone amplifier with preamplifier Enjoy music over headphones and over speakers equally excellently with the superior VOLTAiR technology – that’s why we developed Phonitor x.
The Phonitor x offers connections for standard headphones with a jack plug and for balanced headphones a 4-pin XLR connector. Thanks to the enormous output power of 18 watts, all headphones are driven effortlessly.
The OUTPUT switch turns the headphone amplifier into a preamplifier – simply switch from headphones to speakers and the selected source signal goes to both analog audio outputs, RCA and XLR. In the center position (mute), no signal reaches the outputs. The VU meters light up red.
or to the active loudspeakers you can use the balanced XLR- for long, and the RCA sockets for short cable runs. Practical is the AMP CTL sockets to which power amplifiers with 12V trigger inputs can be connected to switch them on and off together with Phonitor x.
is the big 45mm Volume control? Its mass together with the motorised Alps RK27 “Big Blue” potentiometer enhances the “spoon in the honey” feeling even further. The red marker LED makes the setting visible even in darkened environments.
Volume RC
The volume can be remotely controlled with any infrared remote control, that the Phonitor x simply learns. To do this, press the IR programming button and then the buttons for louder and quieter.
Two mechanical VU meters visualize the input levels for the left and right audio channel.
is not always easy. By our very nature, hearing can be leaning more to the left or more to the right. This is especially obvious when listening with headphones.
That’s why Phonitor x has the uniquely finely resolved laterality control. With it, the center can be found perfectly.
With the mode switch, you can choose between stereo or mono playback. To the right, the laterality control is switched on.
As a company our primary goal is to provide a seamless service that results in customer satisfaction. We aim to deliver within 3 working days. Unfortunately, there may be occasions where this time frame may not be met due to unforeseen circumstances; in this instance, we deliver product/s as soon as we can. All delivery charges are included within the prices quoted, unless otherwise specified.
All small items are usually delivered between 9am and 6pm, on a Monday to Friday, unless a Saturday delivery is requested. Follow My Parcel is an industry-changing innovation from DPD Local, which will give your customers unparalleled levels of information and peace of mind.Not only will your customers receive a one hour delivery timeslot, but they’ll now also be able to track the progress of their parcels on a map as our drivers make their way to the delivery addresses. Follow My Parcel will: